DVL 400
The Digital Video Logger (DVL) with embedded software provides user control, data saving and real-time display of the pulseEKKO PRO GPR data.
Key features are:
- High speed processing and display
- Bright, high contrast, sunlight visible LCD screen
- Weather-proof
- Support of large flash storage memory
- Serial port for GPS integration
|
 |
Back to top
DVL Carrier
|
|
The DVL carrier is used
to hold the DVL in front
of an operator. |
Back to top
Wheel Odometer
Big wheel odometer
Designed for rough terrain. Primarily designed to
be used with the hand towed transducer system.
It has a T-shaped arm for easy attachment to the
transducer skid plates. The odometer cable can
be attached to either the transmitting or receiving
transducers. |
 |
Small wheel odometer
Designed for smooth terrain such as concrete floors.
Designed to be used with the hand towed transducer
system. It has a mounting post and pin for easy
attachment to the transducer skid plates.
The odometer cable can be attached to either the
transmitting or receiving transducers.
|
 |
Back to top
Multi-Channel Adapter
The Multi-Channel Adapter connects standard pulseEKKO PRO systems to allow multi-channel data acquisition.
- Any combination up to 8 transmitters and receivers simultaneously
- Interactive channel setup and replay
- Each channel displayed in real time
- Data recorded to a multiplexed data file and sorted into individual data files using the EKKO_Demux software
- Data analysis with standard software: EKKO_View, EKKO_Mapper and EKKO_3D
- Greatly increased productivity
- Allows a wide variety of advanced GPR surveys including cross-line, in-line, fixed-frequency, multi-frequency, CMP, WARR and multi-polarization
Back to top
20m Fibre Optic Cables
 |
This plastic fibre optic cable is used to connect the pulseEKKO PRO control unit to the receiver or the transmitter.
It has strain reliefs at one end which attach to the transmitter or receiver.
The other end has a dual cable adapter which is intended to go into the electrical to F.O. converters attached to the control module. The cable is 20m (60 feet) long and is needed for CMP type surveys. |
Back to top
10/30m Transducer Cables
This cable is used to link the pulseEKKO PRO control unit to a transducer. The cable is secured in place with latches.
|
 |
 |
| 10m (30 feet) long |
30m (100 feet) long |
| These cables have a connector to allow an odometer wheel to be plugged in |
|
There are 3 types of cables:
- Cables with no input for odometers or remote triggers
- Cables with a connector to allow an odometer wheel to be plugged in (shown above)
- The transducer connector end of the cable has a Canbus connector for attachment of Canbus peripherals such as a beeper/trigger
|
Back to top
Tx, Rx Batteries
|
Commonly referred to as a camcorder battery, this 12 VDC 2.3 Ah rechargeable power supply is used to supply power to the pulseEKKO PRO and pulseEKKO 100A Receiver and Transmitter modules.
Each Receiver or Transmitter module has two battery compartments that are located on opposite sides of the electronic module. One battery is inserted into each compartment. Note that lead acid gel cell batteries are sealed, safe to ship and will not leak. |
Back to top
Belt Battery
The belt battery power supply case is a tough fabric belt and pack which holds a 12V 7.2 Ah lead acid gel cell battery. This rechargeable battery is a flexible lightweight power source for Noggin and pulseEKKO systems. Power connection uses a standard XLR connector.
|
 |
Back to top
Electrical Beeper trigger
 |
The CANBUS Electrical Beeper Trigger is a standard part of the pulseEKKO PRO Base handle package.
The unit plugs into the CANBUS port on the pulseEKKO PRO Control Unit and can be used to either trigger the system from that location or enter fiducial markers. It can also plug into a pulseEKKO PRO transducer cable with a CANBUS connector to allow data acquisition at the transducer. |
Back to top
Fibre Optic Beeper Trigger
The pulseEKKO PRO Fibre optic beeper trigger unit is used to trigger the pulseEKKO PRO
system to collect data with the 12.5, 25, 50,
100 or 200 MHz antenna sets. It serves the
same purpose as the Canbus Electrical beeper trigger but can attach to the handle
of the transmitting antenna so that the antenna operator has control over the data collection.
This unit cannot be used to enter fiducial markers.
|
 |
Back to top
Fibre Optic cable repair kit
 |
The fibre optic cable repair kit contains the replacement parts required to repair fibre optic cables and a couple of spare
1/4 turn fasteners for the handles. |
Back to top
GPS
Various GPS models can be used depending on the accuracy required by your application.
You will also require a
GPS SmartCart Mount if you are installing it on a SmartCart. |
 |
Back to top
EasyGrid
 |
EasyGrid is a simple kit provided by Sensors & Software Inc. to help GPR users with little mapping experience lay out an accurate grid with straight lines and all corners at 90 degree angles.
EasyGrid includes:
- 5 Nails
- 1 Hammer
- 2 x 5 m strings with brass markers every 0.25 m or 1 x 15 foot string with brass markers every foot
- 1 x 7.05 m string or 21 foot 2 inch string.
- 5 yellow plastic disks
- 1 manual
|
Back to top